Wave overhang print

; (derived from slicer end-of-file config block)

; aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaabakv4pp2wuh3oytqqaaaaasuvork5cyii = 
; aaaasuvork5cyii = 
; accel_to_decel_enable = 1
; accel_to_decel_factor = 50%
; activate_air_filtration = 0,0,0,0
; activate_chamber_temp_control = 0,0,0,0
; adaptive_bed_mesh_margin = 0
; adaptive_pressure_advance = 0,0,0,0
; adaptive_pressure_advance_bridges = 0,0,0,0
; adaptive_pressure_advance_model = "0,0,0\n0,0,0";"0,0,0\n0,0,0";"0,0,0\n0,0,0";"0,0,0\n0,0,0"
; adaptive_pressure_advance_overhangs = 0,0,0,0
; additional_cooling_fan_speed = 0,0,0,0
; align_infill_direction_to_model = 0
; alternate_extra_wall = 0
; auxiliary_fan = 1
; bbl_calib_mark_logo = 1
; bbl_use_printhost = 0
; bed_custom_model = 
; bed_custom_texture = 
; bed_exclude_area = 0x0
; bed_mesh_max = 267,267
; bed_mesh_min = 3,3
; bed_mesh_probe_distance = 50,50
; bed_shape = 0.5x1,270.5x1,270.5x271,0.5x271
; bed_temperature_formula = by_highest_temp
; before_layer_change_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\nTIMELAPSE_TAKE_FRAME\nDEFECT_DETECTION_DETECT
; best_object_pos = 0.5,0.5
; bottom_shell_layers = 5
; bottom_shell_thickness = 0
; bottom_solid_infill_flow_ratio = 1
; bottom_surface_density = 100%
; bottom_surface_pattern = concentric
; bridge_acceleration = 50%
; bridge_angle = 0
; bridge_density = 100%
; bridge_flow = 1
; bridge_no_support = 0
; bridge_speed = 50
; brim_ears_detection_length = 1
; brim_ears_max_angle = 125
; brim_object_gap = 0.1
; brim_type = auto_brim
; brim_use_efc_outline = 0
; brim_width = 5
; calib_flowrate_topinfill_special_order = 0
; chamber_temperature = 0,0,0,0
; change_extrusion_role_gcode = 
; change_filament_gcode = ;===== date: 20251213=====================\n; Change Tool[previous_extruder] -> Tool[next_extruder] (layer [layer_num])\n{\nlocal max_speed_toolchange = 350.0;\nlocal wait_for_extruder_temp = true;\nposition[2] = position[2] + 2.0;\nlocal speed_toolchange = max_speed_toolchange;\nif travel_speed < max_speed_toolchange then\n      speed_toolchange = travel_speed;\nendif\n\"G91\nG1 Z1.5 F1800\nG90\n\";\n\"G1 F\" + (speed_toolchange * 60) + \"\n\";\nif wait_for_extruder_temp and not((layer_num < 0) and (next_extruder == initial_tool)) then\n      \"\n\";\n      \"; \" + layer_num + \"\n\";\n      if layer_num == 0 then\n            \"M109 S\" + first_layer_temperature[next_extruder] + \" T\" + next_extruder + \"\n\";\n      else\n            \"M109 S\" + temperature[next_extruder] + \" T\" + next_extruder + \"\n\";\n      endif\nendif\n\"M400\" + \"\n\";\n\"T\" + next_extruder + \"\n\";\nif filament_type[next_extruder] == \"PVA\" then\n\"SET_VELOCITY_LIMIT ACCEL=3000\n\";\nelse\nendif\nif previous_extruder != next_extruder and initial_extruder != next_extruder then\n\"SM_PRINT_PREEXTRUDE_FILAMENT INDEX=\" + next_extruder + \"\n\";\nendif\n\"G90\n\";\n}\n
; close_fan_the_first_x_layers = 3,3,3,3
; combine_brims = 0
; complete_print_exhaust_fan_speed = 80,80,80,80
; cool_plate_temp = 0,0,0,0
; cool_plate_temp_initial_layer = 0,0,0,0
; cooling_tube_length = 5
; cooling_tube_retraction = 91.5
; counterbore_hole_bridging = none
; curr_bed_type = High Temp Plate
; default_acceleration = 4000
; default_bed_type = Textured PEI Plate
; default_filament_colour = ;;;
; default_filament_profile = "Snapmaker PLA"
; default_jerk = 0
; default_junction_deviation = 0
; default_nozzle_volume_type = Standard,Standard,Standard,Standard
; default_print_profile = 0.20mm Standard @Snapmaker
; deretraction_speed = 35,35,35,35
; detect_narrow_internal_solid_infill = 1
; detect_overhang_wall = 1
; detect_thin_wall = 0
; different_settings_to_system = bottom_surface_pattern;internal_solid_infill_pattern;sparse_infill_pattern;top_surface_pattern;wall_loops;additional_cooling_fan_speed;close_fan_the_first_x_layers;fan_max_speed;fan_min_speed;hot_plate_temp;hot_plate_temp_initial_layer;additional_cooling_fan_speed;close_fan_the_first_x_layers;fan_max_speed;fan_min_speed;hot_plate_temp;hot_plate_temp_initial_layer;additional_cooling_fan_speed;close_fan_the_first_x_layers;fan_max_speed;fan_min_speed;hot_plate_temp;hot_plate_temp_initial_layer;additional_cooling_fan_speed;close_fan_the_first_x_layers;fan_max_speed;fan_min_speed;hot_plate_temp;hot_plate_temp_initial_layer;print_host
; disable_m73 = 0
; dont_filter_internal_bridges = disabled
; dont_slow_down_outer_wall = 0,0,0,0
; draft_shield = disabled
; during_print_exhaust_fan_speed = 60,60,60,60
; elefant_foot_compensation = 0.15
; elefant_foot_compensation_layers = 1
; emit_machine_limits_to_gcode = 1
; enable_arc_fitting = 1
; enable_extra_bridge_layer = disabled
; enable_filament_ramming = 0
; enable_long_retraction_when_cut = 0
; enable_overhang_bridge_fan = 1,1,1,1
; enable_overhang_speed = 1
; enable_power_loss_recovery = printer_configuration
; enable_pressure_advance = 1,1,1,1
; enable_prime_tower = 0
; enable_support = 0
; enable_tower_interface_cooldown_during_tower = 0
; enable_tower_interface_features = 0
; enable_wrapping_detection = 0
; enforce_support_layers = 0
; eng_plate_temp = 0,0,0,0
; eng_plate_temp_initial_layer = 0,0,0,0
; ensure_vertical_shell_thickness = ensure_all
; exclude_object = 1
; extra_loading_move = -2
; extra_perimeters_on_overhangs = 0
; extra_solid_infills = 
; extruder_ams_count = 1#0|4#0;
; extruder_clearance_height_to_lid = 130
; extruder_clearance_height_to_rod = 60
; extruder_clearance_radius = 80
; extruder_colour = #26A69A;#00C1AE;#F4E2C1;#ED1C24
; extruder_offset = 0x0,0x0,0x0,0x0
; extruder_printable_area = 
; extruder_printable_height = 0,0,0,0
; extruder_type = Direct Drive,Direct Drive,Direct Drive,Direct Drive
; extruder_variant_list = "Direct Drive Standard";"Direct Drive Standard";"Direct Drive Standard";"Direct Drive Standard"
; extrusion_rate_smoothing_external_perimeter_only = 0
; fan_cooling_layer_time = 100,100,100,100
; fan_kickstart = 0
; fan_max_speed = 50,50,50,50
; fan_min_speed = 50,50,50,50
; fan_speedup_overhangs = 1
; fan_speedup_time = 0
; filament_adaptive_volumetric_speed = 0,0,0,0
; filament_adhesiveness_category = 0,0,0,0
; filament_change_length = 10,10,10,10
; filament_colour = #26A69A;#00C1AE;#F4E2C1;#ED1C24
; filament_colour_type = 1;1;1;1
; filament_cooling_final_speed = 60,60,60,60
; filament_cooling_initial_speed = 35,35,35,35
; filament_cooling_moves = 2,2,2,2
; filament_cost = 60,60,60,60
; filament_density = 1.24,1.24,1.24,1.24
; filament_diameter = 1.75,1.75,1.75,1.75
; filament_end_gcode = ;;;
; filament_extruder_variant = "Direct Drive Standard";"Direct Drive Standard";"Direct Drive Standard";"Direct Drive Standard"
; filament_flow_ratio = 0.98,0.98,0.98,0.98
; filament_flush_temp = 0,0,0,0
; filament_flush_volumetric_speed = 0,0,0,0
; filament_ids = 14170311270;14170311270;14170311270;14170311270
; filament_is_support = 0,0,0,0
; filament_loading_speed = 35,35,35,35
; filament_loading_speed_start = 35,35,35,35
; filament_map = 1,2,3,4
; filament_map_mode = Auto For Flush
; filament_max_volumetric_speed = 14,14,14,14
; filament_minimal_purge_on_wipe_tower = 0,0,0,0
; filament_multi_colour = #26A69A;#00C1AE;#F4E2C1;#ED1C24
; filament_multitool_ramming = 0,0,0,0
; filament_multitool_ramming_flow = 10,10,10,10
; filament_multitool_ramming_volume = 0,0,0,0
; filament_notes = ;;;
; filament_printable = 3,3,3,3
; filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6";"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6";"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6";"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
; filament_retraction_speed = 60,60,60,60
; filament_self_index = 1,2,3,4
; filament_settings_id = "Snapmaker PLA @U1 - HEIZ70";"Snapmaker PLA @U1 - HEIZ70";"Snapmaker PLA @U1 - HEIZ70";"Snapmaker PLA @U1 - HEIZ70"
; filament_shrink = 100%,100%,100%,100%
; filament_shrinkage_compensation_z = 100%,100%,100%,100%
; filament_soluble = 0,0,0,0
; filament_stamping_distance = 0,0,0,0
; filament_stamping_loading_speed = 0,0,0,0
; filament_start_gcode = ;;;
; filament_toolchange_delay = 0,0,0,0
; filament_tower_interface_pre_extrusion_dist = 10,10,10,10
; filament_tower_interface_pre_extrusion_length = 0,0,0,0
; filament_tower_interface_print_temp = -1,-1,-1,-1
; filament_tower_interface_purge_volume = 20,20,20,20
; filament_tower_ironing_area = 4,4,4,4
; filament_type = PLA;PLA;PLA;PLA
; filament_unloading_speed = 35,35,35,35
; filament_unloading_speed_start = 35,35,35,35
; filament_vendor = Snapmaker;Snapmaker;Snapmaker;Snapmaker
; file_start_gcode = 
; filename_format = {input_filename_base}_{filament_type[0]}_{print_time}.gcode
; fill_multiline = 1
; filter_out_gap_fill = 0
; first_layer_bed_temperature = 70
; first_layer_flow_ratio = 1
; first_layer_height = 0.200
; first_layer_print_sequence = 0
; first_layer_temperature = 220
; flush_into_infill = 0
; flush_into_objects = 0
; flush_into_support = 1
; flush_multiplier = 0.3,1,1,1
; flush_volumes_matrix = 0,70,161,102,61,0,170,105,94,104,0,97,152,157,181,0,0,232,535,341,203,0,568,350,312,348,0,324,508,522,602,0,0,232,535,341,203,0,568,350,312,348,0,324,508,522,602,0,0,232,535,341,203,0,568,350,312,348,0,324,508,522,602,0
; flush_volumes_vector = 140,140,140,140,140,140,140,140
; full_fan_speed_layer = 0,0,0,0
; fuzzy_skin = disabled_fuzzy
; fuzzy_skin_first_layer = 0
; fuzzy_skin_mode = displacement
; fuzzy_skin_noise_type = classic
; fuzzy_skin_octaves = 4
; fuzzy_skin_persistence = 0.5
; fuzzy_skin_point_distance = 0.3
; fuzzy_skin_scale = 1
; fuzzy_skin_thickness = 0.2
; gap_fill_flow_ratio = 1
; gap_fill_target = nowhere
; gap_infill_speed = 230
; gcode_add_line_number = 0
; gcode_comments = 0
; gcode_flavor = klipper
; gcode_label_objects = 1
; grab_length = 0
; has_scarf_joint_seam = 0
; head_wrap_detect_zone = 
; high_current_on_filament_swap = 0
; hole_to_polyhole = 0
; hole_to_polyhole_threshold = 0.01
; hole_to_polyhole_twisted = 1
; host_type = octoprint
; hot_plate_temp = 70,70,70,70
; hot_plate_temp_initial_layer = 70,70,70,70
; idle_temperature = 0,0,0,0
; independent_support_layer_height = 1
; infill_anchor = 400%
; infill_anchor_max = 20
; infill_combination = 0
; infill_combination_max_layer_height = 100%
; infill_direction = 45
; infill_jerk = 9
; infill_lock_depth = 1
; infill_overhang_angle = 60
; infill_shift_step = 0.4
; infill_wall_overlap = 15%
; inherits_group = ;"Snapmaker PLA @U1";"Snapmaker PLA @U1";"Snapmaker PLA @U1";"Snapmaker PLA @U1";"Snapmaker U1 (0.4 nozzle)"
; initial_layer_acceleration = 500
; initial_layer_infill_speed = 105
; initial_layer_jerk = 9
; initial_layer_line_width = 0.5
; initial_layer_min_bead_width = 85%
; initial_layer_print_height = 0.2
; initial_layer_speed = 50
; initial_layer_travel_speed = 100%
; inner_wall_acceleration = 10000
; inner_wall_flow_ratio = 1
; inner_wall_jerk = 9
; inner_wall_line_width = 0.45
; inner_wall_speed = 150
; interface_shells = 0
; interlocking_beam = 0
; interlocking_beam_layer_count = 2
; interlocking_beam_width = 0.8
; interlocking_boundary_avoidance = 2
; interlocking_depth = 2
; interlocking_orientation = 22.5
; internal_bridge_angle = 0
; internal_bridge_density = 100%
; internal_bridge_fan_speed = -1,-1,-1,-1
; internal_bridge_flow = 1
; internal_bridge_speed = 150%
; internal_solid_infill_acceleration = 100%
; internal_solid_infill_flow_ratio = 1
; internal_solid_infill_line_width = 0.42
; internal_solid_infill_pattern = concentric
; internal_solid_infill_speed = 180
; ironing_angle = 0
; ironing_angle_fixed = 0
; ironing_fan_speed = -1,-1,-1,-1
; ironing_flow = 10%
; ironing_inset = 0
; ironing_pattern = rectilinear
; ironing_spacing = 0.15
; ironing_speed = 30
; ironing_type = no ironing
; is_infill_first = 0
; lateral_lattice_angle_1 = -45
; lateral_lattice_angle_2 = 45
; layer_change_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]\nSET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}\nSET_PRINT_STATS_INFO CURRENT_LAYER={layer_num+1}
; layer_height = 0.12
; line_width = 0.42
; long_retractions_when_cut = 0,0,0,0
; long_retractions_when_ec = 0,0,0,0
; machine_end_gcode = PRINT_END\nTIMELAPSE_STOP
; machine_load_filament_time = 0
; machine_max_acceleration_e = 5000,5000,5000,5000,5000,5000,5000,5000
; machine_max_acceleration_extruding = 25000,25000,25000,25000,25000,25000,25000,25000
; machine_max_acceleration_retracting = 5000,5000,5000,5000,5000,5000,5000,5000
; machine_max_acceleration_travel = 25000,25000,25000,25000,25000,25000,25000,25000
; machine_max_acceleration_x = 25000,25000,25000,25000,25000,25000,25000,25000
; machine_max_acceleration_y = 25000,25000,25000,25000,25000,25000,25000,25000
; machine_max_acceleration_z = 500,200,500,500,500,500,500,500
; machine_max_jerk_e = 2.5,2.5,2.5,2.5,2.5,2.5,2.5,2.5
; machine_max_jerk_x = 9,9,9,9,9,9,9,9
; machine_max_jerk_y = 9,9,9,9,9,9,9,9
; machine_max_jerk_z = 3,0.4,3,3,3,3,3,3
; machine_max_junction_deviation = 0.01
; machine_max_speed_e = 30,25,30,30,30,30,30,30
; machine_max_speed_x = 1000,200,1000,1000,1000,1000,1000,1000
; machine_max_speed_y = 1000,200,1000,1000,1000,1000,1000,1000
; machine_max_speed_z = 20,12,20,20,20,20,20,20
; machine_min_extruding_rate = 0,0
; machine_min_travel_rate = 0,0
; machine_pause_gcode = M600
; machine_start_gcode = SET_PRINT_AUTO_BED_LEVELING ENABLE=1\nSET_TIME_LAPSE_CAMERA ENABLE=1\n;===== date: 20251222 =====================\n\nPRINT_START\nDEFECT_DETECTION_START\nSET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}\nSET_PRINT_STATS_INFO CURRENT_LAYER=0\nTIMELAPSE_START\nM140 S{bed_temperature_initial_layer_single}\nM104 T{initial_extruder} S140\nM204 S10000\n\nG28 X Y\n;===== 床面异物检测 ========\nT{initial_extruder}\nG90\nDEFECT_DETECTION_DETECT_BED\n;===== 取放头检测 =================\nSM_PRINT_CHECK_SWITCH_EXTRUDER\n\n;===== 自动进料 & 挤出流量 & 预挤出 ======================\nSM_PRINT_EXTRUDER_PREHEAT EXTRUDER=1 TEMP=140\nSM_PRINT_AUTO_FEED EXTRUDER=0\nSM_PRINT_FLOW_CALIBRATE EXTRUDER=0\nSM_PRINT_EXTRUDER_PREHEAT EXTRUDER=2 TEMP=140\nSM_PRINT_AUTO_FEED EXTRUDER=1\nSM_PRINT_FLOW_CALIBRATE EXTRUDER=1\nSM_PRINT_EXTRUDER_PREHEAT EXTRUDER=3 TEMP=140\nSM_PRINT_AUTO_FEED EXTRUDER=2\nSM_PRINT_FLOW_CALIBRATE EXTRUDER=2\nSM_PRINT_AUTO_FEED EXTRUDER=3\nSM_PRINT_FLOW_CALIBRATE EXTRUDER=3\nM104 S0 T0 A0\nM104 S0 T1 A0\nM104 S0 T2 A0\nM104 S0 T3 A0\nM104 T{initial_extruder} S{nozzle_temperature[initial_extruder] - 90}\n\n;===== 粗回零 =================\nT{initial_extruder}\nM106 S255\nM106 P2 S0\nMOVE_TO_DISCARD_FILAMENT_POSITION\nM109 T{initial_extruder} S{nozzle_temperature[initial_extruder] - 90}\nROUGHLY_CLEAN_NOZZLE_WITH_DISCARD\nMOVE_TO_XY_IDLE_POSITION_EXTRUDER\nG28 Z I140 J140\n\n;===== 检测钢板 =================\nDETECT_BED_PLATE\n\n;===== 深度清洁喷嘴 =================\nG90\nG0 Z5 F10000\nMOVE_TO_DISCARD_FILAMENT_POSITION\nM109 S{nozzle_temperature[initial_extruder] - 50}\nROUGHLY_CLEAN_NOZZLE\nMOVE_TO_XY_IDLE_POSITION_EXTRUDER\nFINELY_CLEAN_NOZZLE_STAGE_1\nM104 S{nozzle_temperature[initial_extruder] - 90}\nG0 Z5 F10000\nMOVE_TO_DISCARD_FILAMENT_POSITION\nROUGHLY_CLEAN_NOZZLE\nMOVE_TO_XY_IDLE_POSITION_EXTRUDER\nFINELY_CLEAN_NOZZLE_STAGE_2\n\n;===== 精回零 =================\nM106 S255\nM109 S{nozzle_temperature[initial_extruder] - 90}\nM190 S{bed_temperature_initial_layer_single}\nM107 P2\nG90\nG0 Z5 F10000\nG28 Z\n\n;===== 热床调平 =================\n; Always pass `ADAPTIVE_MARGIN=0` because Orca has already handled `adaptive_bed_mesh_margin` internally\n; Make sure to set ADAPTIVE to 0 otherwise Klipper will use it's own adaptive bed mesh logic\nBED_MESH_CALIBRATE mesh_min={adaptive_bed_mesh_min[0]},{adaptive_bed_mesh_min[1]} mesh_max={adaptive_bed_mesh_max[0]},{adaptive_bed_mesh_max[1]} ALGORITHM=[bed_mesh_algo] PROBE_COUNT={bed_mesh_probe_count[0]},{bed_mesh_probe_count[1]} ADAPTIVE=0 ADAPTIVE_MARGIN=0\n; Original upstream: BED_MESH_CALIBRATE PROBE_COUNT=11,11\n\n;===== 画起始线 =================\nG90\nG1 Z1.5\nG0 X10 Y3 Z2 F18000\nM109 S{nozzle_temperature_initial_layer[initial_extruder]}\nG1 Z0.2\nM83\nG1 X110 E15 F360\nG1 Z1.5\n\nG90\nM106 S0
; machine_tool_change_time = 5
; machine_unload_filament_time = 0
; make_overhang_printable = 0
; make_overhang_printable_angle = 55
; make_overhang_printable_hole_size = 0
; manual_filament_change = 0
; master_extruder_id = 1
; max_bridge_length = 10
; max_layer_height = 0.32,0.32,0.32,0.32
; max_resonance_avoidance_speed = 90
; max_travel_detour_distance = 0
; max_volumetric_extrusion_rate_slope = 0
; max_volumetric_extrusion_rate_slope_segment_length = 3
; min_bead_width = 85%
; min_feature_size = 25%
; min_layer_height = 0.08,0.08,0.08,0.08
; min_length_factor = 0.5
; min_resonance_avoidance_speed = 40
; min_skirt_length = 0
; min_width_top_surface = 300%
; minimum_sparse_infill_area = 15
; mmu_segmented_region_interlocking_depth = 0
; mmu_segmented_region_max_width = 0
; notes = 
; nozzle_diameter = 0.4,0.4,0.4,0.4
; nozzle_flush_dataset = 0,0,0,0
; nozzle_height = 2.5
; nozzle_hrc = 0
; nozzle_temperature = 220,220,220,220
; nozzle_temperature_initial_layer = 220,220,220,220
; nozzle_temperature_range_high = 240,240,240,240
; nozzle_temperature_range_low = 190,190,190,190
; nozzle_type = stainless_steel,stainless_steel,stainless_steel,stainless_steel
; nozzle_volume = 143,143,143,143
; nozzle_volume_type = Standard,Standard,Standard,Standard
; only_one_wall_first_layer = 0
; only_one_wall_top = 1
; ooze_prevention = 0
; other_layers_print_sequence = 0
; other_layers_print_sequence_nums = 0
; outer_wall_acceleration = 2000
; outer_wall_flow_ratio = 1
; outer_wall_jerk = 9
; outer_wall_line_width = 0.42
; outer_wall_speed = 60
; overhang_1_4_speed = 60
; overhang_2_4_speed = 30
; overhang_3_4_speed = 10
; overhang_4_4_speed = 10
; overhang_fan_speed = 100,100,100,100
; overhang_fan_threshold = 0%,0%,0%,0%
; overhang_flow_ratio = 1
; overhang_reverse = 0
; overhang_reverse_internal_only = 0
; overhang_reverse_threshold = 50%
; parking_pos_retraction = 92
; pellet_flow_coefficient = 0.4157,0.4157,0.4157,0.4157
; pellet_modded_printer = 0
; physical_extruder_map = 0
; post_process = 
; precise_outer_wall = 1
; precise_z_height = 0
; preferred_orientation = 0
; preheat_steps = 1
; preheat_time = 30
; pressure_advance = 0.02,0.02,0.02,0.02
; prime_tower_brim_width = 3
; prime_tower_enable_framework = 0
; prime_tower_flat_ironing = 0
; prime_tower_infill_gap = 150%
; prime_tower_skip_points = 1
; prime_tower_width = 35
; prime_volume = 30
; print_compatible_printers = "Snapmaker U1 (0.4 nozzle)"
; print_extruder_id = 1,1,1,1
; print_extruder_variant = "Direct Drive Standard";"Direct Drive Standard";"Direct Drive Standard";"Direct Drive Standard"
; print_flow_ratio = 1
; print_order = default
; print_sequence = by layer
; print_settings_id = 0.12 High Quality @Snapmaker U1 (0.4 nozzle)
; printable_area = 0.5x1,270.5x1,270.5x271,0.5x271
; printable_height = 270.05
; printer_agent = snapmaker
; printer_extruder_id = 1,2,3,4
; printer_extruder_variant = "Direct Drive Standard";"Direct Drive Standard";"Direct Drive Standard";"Direct Drive Standard"
; printer_model = Snapmaker U1
; printer_notes = 
; printer_settings_id = Snapmaker U1 (0.4 nozzle) - Copy
; printer_structure = undefine
; printer_technology = FFF
; printer_variant = 0.4
; printhost_authorization_type = key
; printhost_ssl_ignore_revoke = 0
; printing_by_object_gcode = 
; purge_in_prime_tower = 0
; raft_contact_distance = 0.1
; raft_expansion = 1.5
; raft_first_layer_density = 90%
; raft_first_layer_expansion = 2
; raft_layers = 0
; reduce_crossing_wall = 0
; reduce_fan_stop_start_freq = 1,1,1,1
; reduce_infill_retraction = 1
; required_nozzle_hrc = 3,3,3,3
; resolution = 0.012
; resonance_avoidance = 1
; retract_before_wipe = 0%,0%,0%,0%
; retract_length_toolchange = 10,10,10,10
; retract_lift_above = 0,0,0,0
; retract_lift_below = 269,269,269,269
; retract_lift_enforce = All Surfaces,All Surfaces,All Surfaces,All Surfaces
; retract_restart_extra = 0,0,0,0
; retract_restart_extra_toolchange = 0,0,0,0
; retract_when_changing_layer = 1,1,1,1
; retraction_distances_when_cut = 18,18,18,18
; retraction_distances_when_ec = 10,10,10,10
; retraction_length = 0.8,0.8,0.8,0.8
; retraction_minimum_travel = 1,1,1,1
; retraction_speed = 40,40,40,40
; role_based_wipe_speed = 1
; scan_first_layer = 0
; scarf_angle_threshold = 155
; scarf_joint_flow_ratio = 1
; scarf_joint_speed = 100%
; scarf_overhang_threshold = 40%
; seam_gap = 10%
; seam_position = aligned
; seam_slope_conditional = 0
; seam_slope_entire_loop = 0
; seam_slope_inner_walls = 0
; seam_slope_min_length = 20
; seam_slope_start_height = 0
; seam_slope_steps = 10
; seam_slope_type = none
; set_other_flow_ratios = 0
; silent_mode = 0
; single_extruder_multi_material = 0
; single_extruder_multi_material_priming = 0
; single_loop_draft_shield = 0
; skeleton_infill_density = 25%
; skeleton_infill_line_width = 100%
; skin_infill_density = 25%
; skin_infill_depth = 2
; skin_infill_line_width = 100%
; skirt_distance = 2
; skirt_height = 1
; skirt_loops = 0
; skirt_speed = 50
; skirt_start_angle = -135
; skirt_type = combined
; slice_closing_radius = 0.049
; slicing_mode = regular
; slow_down_for_layer_cooling = 1,1,1,1
; slow_down_layer_time = 8,8,8,8
; slow_down_layers = 0
; slow_down_min_speed = 15,15,15,15
; slowdown_for_curled_perimeters = 0
; small_area_infill_flow_compensation = 0
; small_area_infill_flow_compensation_model = 0,0;"\n0.2,0.4444";"\n0.4,0.6145";"\n0.6,0.7059";"\n0.8,0.7619";"\n1.5,0.8571";"\n2,0.8889";"\n3,0.9231";"\n5,0.9520";"\n10,1"
; small_perimeter_speed = 50%
; small_perimeter_threshold = 0
; solid_infill_direction = 45
; solid_infill_filament = 1
; solid_infill_rotate_template = 
; sparse_infill_acceleration = 100%
; sparse_infill_density = 15%
; sparse_infill_filament = 1
; sparse_infill_flow_ratio = 1
; sparse_infill_line_width = 0.45
; sparse_infill_pattern = concentric
; sparse_infill_rotate_template = 
; sparse_infill_speed = 180
; spiral_finishing_flow_ratio = 0
; spiral_mode = 0
; spiral_mode_max_xy_smoothing = 200%
; spiral_mode_smooth = 0
; spiral_starting_flow_ratio = 0
; staggered_inner_seams = 0
; standby_temperature_delta = -5
; start_end_points = 30x-3,54x245
; supertack_plate_temp = 35,35,35,35
; supertack_plate_temp_initial_layer = 35,35,35,35
; support_air_filtration = 1
; support_angle = 0
; support_base_pattern = default
; support_base_pattern_spacing = 2.5
; support_bottom_interface_spacing = 0.5
; support_bottom_z_distance = 0.12
; support_chamber_temp_control = 1
; support_critical_regions_only = 0
; support_expansion = 0
; support_filament = 0
; support_flow_ratio = 1
; support_interface_bottom_layers = 2
; support_interface_filament = 0
; support_interface_flow_ratio = 1
; support_interface_loop_pattern = 0
; support_interface_not_for_body = 1
; support_interface_pattern = auto
; support_interface_spacing = 0.5
; support_interface_speed = 80
; support_interface_top_layers = 2
; support_ironing = 0
; support_ironing_flow = 10%
; support_ironing_pattern = rectilinear
; support_ironing_spacing = 0.1
; support_line_width = 0.42
; support_material_interface_fan_speed = -1,-1,-1,-1
; support_multi_bed_types = 0
; support_object_first_layer_gap = 0.2
; support_object_skip_flush = 0
; support_object_xy_distance = 0.35
; support_on_build_plate_only = 0
; support_remaining_areas_after_wave_overhangs = 1
; support_remove_small_overhang = 1
; support_speed = 150
; support_style = default
; support_threshold_angle = 20
; support_threshold_overlap = 50%
; support_top_z_distance = 0.12
; support_type = normal(auto)
; symmetric_infill_y_axis = 0
; temperature_vitrification = 154,154,154,154
; template_custom_gcode = 
; textured_cool_plate_temp = 40,40,40,40
; textured_cool_plate_temp_initial_layer = 40,40,40,40
; textured_plate_temp = 0,0,0,0
; textured_plate_temp_initial_layer = 0,0,0,0
; thick_bridges = 0
; thick_internal_bridges = 1
; thumbnails = 48x48/PNG, 300x300/PNG
; thumbnails_format = PNG
; time_cost = 0
; time_lapse_gcode = 
; timelapse_type = 0
; top_bottom_infill_wall_overlap = 25%
; top_shell_layers = 5
; top_shell_thickness = 0.6
; top_solid_infill_flow_ratio = 1
; top_surface_acceleration = 2000
; top_surface_density = 100%
; top_surface_jerk = 9
; top_surface_line_width = 0.42
; top_surface_pattern = concentric
; top_surface_speed = 150
; travel_acceleration = 10000
; travel_jerk = 12
; travel_slope = 3,3,3,3
; travel_speed = 500
; travel_speed_z = 0
; tree_support_angle_slow = 25
; tree_support_auto_brim = 1
; tree_support_branch_angle = 45
; tree_support_branch_angle_organic = 40
; tree_support_branch_diameter = 2
; tree_support_branch_diameter_angle = 5
; tree_support_branch_diameter_organic = 2
; tree_support_branch_distance = 5
; tree_support_branch_distance_organic = 1
; tree_support_brim_width = 3
; tree_support_tip_diameter = 0.8
; tree_support_top_rate = 30%
; tree_support_wall_count = 0
; upward_compatible_machine = 
; use_firmware_retraction = 0
; use_relative_e_distances = 1
; volumetric_speed_coefficients = ;;;
; wall_direction = ccw
; wall_distribution_count = 1
; wall_filament = 1
; wall_generator = arachne
; wall_loops = 3
; wall_sequence = inner wall/outer wall
; wall_transition_angle = 10
; wall_transition_filter_deviation = 25%
; wall_transition_length = 100%
; wave_overhang_algorithm = andersons
; wave_overhang_debug_gcode = 1
; wave_overhang_end_retract_length = 0
; wave_overhang_fan_speed = 100
; wave_overhang_floor_layers = 2
; wave_overhang_flow_mm3_per_mm = 0.15
; wave_overhang_line_spacing = 0.35
; wave_overhang_max_iterations = 0
; wave_overhang_min_angle = 0
; wave_overhang_min_layer_time = 0
; wave_overhang_min_length = 0
; wave_overhang_min_new_area = 0.01
; wave_overhang_min_wave_time = 0
; wave_overhang_minimum_width = 0.7
; wave_overhang_nozzle_temp = 0
; wave_overhang_outer_perimeters = 1
; wave_overhang_pattern = smart
; wave_overhang_perimeter_overlap = 0.1
; wave_overhang_print_speed = 2
; wave_overhang_ring_overlap = 0.15
; wave_overhang_seam_mode = alternating
; wave_overhang_spacing_mode = uniform
; wave_overhang_travel_speed = 40
; wave_overhangs = 0
; wave_overhangs_instead_of_bridges = 0
; wipe = 1,1,1,1
; wipe_before_external_loop = 0
; wipe_distance = 2,2,2,2
; wipe_on_loops = 0
; wipe_speed = 80%
; wipe_tower_bridging = 10
; wipe_tower_cone_angle = 30
; wipe_tower_extra_flow = 100%
; wipe_tower_extra_rib_length = 0
; wipe_tower_extra_spacing = 100%
; wipe_tower_filament = 1
; wipe_tower_fillet_wall = 1
; wipe_tower_max_purge_speed = 90
; wipe_tower_no_sparse_layers = 0
; wipe_tower_rib_width = 8
; wipe_tower_rotation_angle = 0
; wipe_tower_type = type2
; wipe_tower_wall_type = rib
; wipe_tower_x = 165,165
; wipe_tower_y = 237.626,244.697
; wiping_volumes_extruders = 70,70,70,70,70,70,70,70,70,70
; wrapping_detection_gcode = 
; wrapping_detection_layers = 20
; wrapping_exclude_area = 
; xy_contour_compensation = 0
; xy_hole_compensation = 0
; z_hop = 0.4,0.4,0.4,0.4
; z_hop_types = Auto Lift,Auto Lift,Auto Lift,Auto Lift
; z_offset = 0